back to the product overview

Frequently asked questions

ZENEC E>GO device cannot be run / turned on when ignition of vehicle is off.

Answer: E>GO units are connected to the CAN network of the vehicle they are mounted to and require CAN data for certain functions to operate correctly. CAN data is only present in the vehicle, when ignition status is on – for this reason operation of the unit is not possible when ignition of the car (ACC) has been set to its off position.
Based on this technical background, the unit will not discharge the battery of the vehicle when the driver forgets to switch off the E>GO device before he leaves the car, and the DME of the vehicle will not periodically check if there is a non identified device still active in the on-board electrical system, but instead the E>GO device and the vehicles in-car electronics enter “sleep mode” together.

Navigation function of the ZENEC sat nav is sometimes erroneous, for example at crossings or a traffic circle.

Answer: Please consider that ZENEC deploys digital map data of the market leader TELE Atlas. With full EU content and routing and signalization of streets being modified on a daily bases, it can easily happen that certain parts of digitalized map data are wrong or not fully up to date. Please contact the support section of TELEATLAS directly, using the provided link – because such issues should ideally be reported by the end user that has stumbled over it (first hand info): http://mapinsight.teleatlas.com/mapfeedback/index.php

Can i use my ex works CD-Changer together with the ZE-NC2010?

Answer: The ZE-NC2010 has no connection facility for a CD-Changer.

What conditions must be met, to install the ZE-NC2010 unit?

Answer: The vehicle must be equipped with the "OE radio prearrangement" from the factory, to allow straightforward installation of the ZE-NC2010. The physical appearance of the OE installed radio must be identical with the ZE-NC2010, else installation is not possible. Please refer to the compatibility list.

Can I continue to use the OE installed GPS-antenna of my car?

Answer: Yes, the OE mounted GPS antennas are flawlessly working with the ZE-NC2010 (Fakra connector). The included E>GO GPS kit antenna, however, is very well adapted to the E>GO and will, most likely, do an even better job.

Is the ex works hands-free device compatible?

Answer: No. But the ZE-NC2010 sports an integrated high-quality hands-free device from marketleader PARROT. In case your phone has Bluetooth ability, the E>GO ZE-NC2010 offers a comprehensive hands-free device function. Once you have paired your mobile with the E>GO, you can handle your calls completely via its touchscreen. Built-In ex works hands-free devices should be completely shut down, by removing the respective fuse (the one in the fuse box). If you omit that, you will probably encounter distortions during parallel operation.

After usage of the external microphone, I changed back to the internal microphone. But the volume is low and the speech intelligibility is bad.

Answer: Out of the box, the internal microphone is activated. If you want to use the external microphone, remove the violet connector with the wire bridge, activate the external microphone in the Bluetooth setup and add the violet connector with the external microphone instead of the wire bridge. If you want to use the internal microphone again, add the wire bridge instead the connector with the external microphone and activate the internal microphone in the Bluetooth setup again. You will find a detailed description of the Bluetooth mode in the main manual. When installing the microphone, take care not to place it near any air streaming nozzle.

Will my park assist still work after mounting the ZENEC?

Answer: Yes. However, your Garage has to  intialise RCD210 (CAN-Bus).

Do the park sensors still work after mounting the ZE-NC2010?

Answer: Yes, the park sensors and their audible messages still work.

My iPhone gets charged, but i cannot replay any file from it.

Answer: Make sure you have the latest software/firmware, on all participating devices, installed. Obsolete or improper software/firmware
may cause severe problems. Use the original ZENEC iPod/iPhone connection cable for full functionality. If the problem persists
disconnect your Apple device and reset it before reconnecting. Consult your Apple manual for further details.

After updating my iPhone/iPod it does not properly connect anymore. How do i solve that?

Answer: Disconnect your iPhone before you switch your E>GO on. Switch off your iPhone/iPod completely by holding HOME and POWER Key pressed for at least 5 Seconds, until  the red "Power off" bar appears. Touch it to shut down. Now connect your iPhone/iPod to the E>GO. It should automatically power on.
If it does not, switch it on manually. Keep the power key pressed for at least two seconds. Your iPhone/iPod connection has been newly initialised. That should remedy your connection problems.

If i invoke a call via voice tag, how do i know which number gets dialled?

Answer: The voice tag call always chooses the number which has been filed under "mobile number". However, this could well be a landline number, if you chose to store it there.

The security code of my E>GO does not work as expected.

Answer: Make sure not to mix it up with the parental lock code. Please
consult the manual for further details.

Interaction with MFD and steering wheel remote is non-functional.

Answer: Please make sure that the brown plug is connected on the rear side. That connector transmits the CAN-Bus signals. For some special car type, you might even need a CAN-Bus update. See other notes concerning CAN-Bus further down in this document.

When starting the engine my E>GO switches off and reboots.

Answer: When the voltage supply drops under approx. 9V your E>GO automatically shuts down to avoid operation faults. Its a self protection scheme and not a defect. You may, however, check your electrical installation (battery worn, bad or corroded ground connections, etc.).

What should i consider playing USB media?

Answer: The USB connector is on the back of the device. It can be rerouted to the dash board or glove compartment by using the included Media Link Box. The USB data carrier should be FAT32 formatted. It should not need more than 400 mA, if no external power is present. We recommend 6.35 cm (2.5 inch) or preferably 4.6 cm (1.8 inch) harddisks. The smaller harddisks need less power and are mechanically more durable.

Which SD-Cards are supported?

Answer: SD/SDHC cards up to 8GB, FAT32 formatted. Anything else may or may not work.

Content on USB / SD data carrier is not recognized even after successful formatting?

It may happen that the file system of the disk got damaged, or that the file allocation table of a data carrier is defect due to erroneous write cycles. There may be different reason for this to happen, such as usage or storage of data carriers and problems occurring at the initial format process.

In such cases, you must format the data carrier once more to get it to work as intended.

Windows Vista and Win7 offer two options, i.e. you can apply a quick format or a full format of carrier. For all cases related to data carriers that seem to cause problems, it is highly suggested to do a full format process. Make sure the check mark for quick format is not set. Also pay attention that the FAT32 file system is selected before you start the format process.

Info: If the disc after formatting is still not recognized by the device, it may be due to an incompatibility of the disk controller chip itself. In such a case, you should use a different data carrier of another brand or manufacturer.

How do i check the software version?

Answer: Tap into the upper left corner to invoke the main menu. Now choose "Setup" (icon with sprocket). Now scroll all the way down and tap "Version".

Why do i need software updates?

Answer: ZENEC frequently releases software updates to add new functionality, correct issues and improve reliability.

Where can i download software updates?

Answer: Released updates may be downloaded from the ZENEC homepage. Go to "Support". Ask your ZENEC dealer, if you have further questions. Do never install any "updates" from other sources, as this might damage your device
irreversibly.

Why can i not use Winzip/Winrar to unpack the update?

Answer: Because data integrity can only be guaranteed when using 7-Zip to unpack. www.7-zip.org

How do i install the updates?

Answer: That depends on device and version. We publish device- and version-specific instructions together with the update.
Do not install the update, before you have entirely read the instructions.

The installation instructions say that I have to use a USB flash drive to update. Can I use a CD instead?

Answer: No, you have to follow the given instructions closely. Otherwise your update will probably fail and you surely risk to damage your device.

I have been recommended to update the CAN-Bus Adapter. Do i need to de-install it to do so?

Answer: No, not necessary. ZENEC has integrated a CAN-Bus updater into its software interface, allowing you to update the CAN-Bus adapter in-circuit using a USB flash drive. Follow the accompanying instructions closely, to avoid any damage.

My problem still persists even after the CAN-Bus update.

Answer: You have to reset the entire board computer completely to set the changes into effect. In order to do so, disconnect the car battery for a few minutes. Afterwards the CAN-Bus adapter changes will be recognized.

back to the product overview