back to the product overview

Frequently asked questions

Navigation function of the ZENEC sat nav is sometimes erroneous, for example at crossings or a traffic circle.

Answer: Please consider that ZENEC deploys digital map data of the market leader TELE Atlas. With full EU content and routing and signalization of streets being modified on a daily bases, it can easily happen that certain parts of digitalized map data are wrong or not fully up to date. Please contact the support section of TELEATLAS directly, using the provided link – because such issues should ideally be reported by the end user that has stumbled over it (first hand info):

http://mapinsight.teleatlas.com/mapfeedback/index.php

My iPod/iPhone gets charged, but is not accessible as a replay source.

Answer: Just make sure that your ZENEC device as well as your iPod/iPhone, have the latest software update installed. Non-fitting or non up-to-date software versions can cause a variety of problems and malfunctions.

Apart from that, we can only guarantee a trouble free functionality if you use the recommended original ZENEC iPod/iPhone connection cable.

If you are sure that the latest software is installed (using the original ZENEC iPod cable) and the problem still persists, then disconnect and reset your iPod/iPhone. Consult your iPod/iPhone manual on how to reset your device.

After updating to iOS4, my iPhone/iPod doesn't work. What can I do? 

1. Turn on your ZENEC device, make sure the iPod or iPhone is not connected or unplug it.
2. Switch off your iPod or iPhone. Turning off these APPLE devices requires you to press both HOME and POWER buttons for approx. 5 seconds. A red button will appear on the touch screen. Slide the red button to the right side to power off your device.
3. Re-connect the iPod or iPhone to your ZENEC device.
4. The iPod or iPhone should automatically turn on. If this is not the case, press the POWER button for 2 seconds to manually power on.
5. After the iPod or iPhone has been initialized following the instructions above, the switch on sequence of your APPLE device reverts back to its initial status (as before the iOS4 update).

What phone number is dialed, with the ZE-NC4110 in voice tag dial mode?

Answer: The ZE-NC4110 will dial the cell phone number. Please pay attention, that the cell phone number must be saved in the category "mobile number" in the phone book of your cell phone.

Can I connect and continue to use the OE installed hands-free kit with the ZE-NC4110?

Answer: No, this is not possible.

After usage of the external microphone, I changed back to the internal microphone. But the volume is low and the speech intelligibility is bad.

Out of the box, the internal microphone is activated. If you want to use the external microphone, remove the violet connector with the wire bridge, activate the external microphone in the Bluetooth setup and add the violet connector with the external microphone instead of the wire bridge. If you want to use the internal microphone again, add the wire bridge instead the connector with the external microphone and activate the internal microphone in the
Bluetooth setup again. You will find a detailed description of the Bluetooth mode
in the main manual.

What phone number is dialed, with the ZE-NC4110 in voice tag dial mode?

Answer: The ZE-NC4110 will dial the cell phone number that is imparted from cell phone. Please pay attention, that the cell phone number must have been saved in the category "mobile number" in the phone book of your cell phone.

The security code doesn't work properly.

Answer: Please be sure, that you do not mean the parental lock feature. Please refer to the manual.

What do I have to consider using an USB device?

Answer: The USB port is located on the back side or on the Media-Link-Box (if connected). The USB device needs to be formatted in FAT32 filesystem. The following files can be read and played: MP3, WMA, DivX5, DivX6, AVI, JPEG. The USB port provides a current of up to 400 mA and accepts external hard drives up to 250 GB.

What do I hae to consider using SDHC cards?

Answer: The SD or SDHC card needs to be formatted in FAT32 filesystem. The following files can be read and played: MP3, WMA, DivX5, DivX6, AVI, JPEG.

Content on USB / SD data carrier is not recognized even after successful formatting?

It may happen that the file system of the disk got damaged, or that the file allocation table of a data carrier is defect due to erroneous write cycles. There may be different reason for this to happen, such as usage or storage of data carriers and problems occurring at the initial format process.

In such cases, you must format the data carrier once more to get it to work as intended.

Windows Vista and Win7 offer two options, i.e. you can apply a quick format or a full format of carrier. For all cases related to data carriers that seem to cause problems, it is highly suggested to do a full format process. Make sure the check mark for quick format is not set. Also pay attention that the FAT32 file system is selected before you start the format process.

Info: If the disc after formatting is still not recognized by the device, it may be due to an incompatibility of the disk controller chip itself. In such a case, you should use a different data carrier of another brand or manufacturer.

back to the product overview